Tuned Yota · Independent Authorized AMSOIL Dealer · Lakeville, Minnesota, USA · This website is owned and operated by an independent AMSOIL Dealer and is not AMSOIL INC.

Tuned Yota FluidsIndependent Authorized AMSOIL Dealer

Service Guide · Lexus GX 460 2010–2013 · 4.6L V8 (1UR-FE)

Lexus GX 460 Oil and Filter Change: Capacity, Grade and Torque (2010-2013)

The GX 460 takes 8.2 US qt (7.8 L) with a filter change and 7.8 qt (7.4 L) without, of an ILSAC multigrade oil, SAE 0W-20 (preferred). Toyota allows SAE 5W-20 if 0W-20 is not available, but says it must be replaced at the next oil change. The drain plug takes a new gasket and 40 N·m (30 ft-lb). The filter is a cartridge element in a cap: the cap tightens to 25 N·m (18 ft-lb) with a special tool, and the manual calls for a new O-ring and a new element every time. On the normal schedule the oil and filter are replaced every 10,000 miles or 12 months, and every 6 months on the severe schedule. The procedure below is the manual's own order of work.

Safety. Required: safety glasses, oil-proof gloves, and the vehicle level on a lift or on jack stands with the wheels chocked. Toyota's caution: prolonged and repeated skin contact with used engine oil removes natural skin oils and used oil contains potentially harmful contaminants, so wear protective clothing and gloves that oil cannot penetrate, wash with soap and water or waterless hand cleaner, and do not use gasoline, thinners or solvents. Dispose of used oil and filters at a designated disposal site. Recommended: a drain pan large enough for 8 quarts and a torque wrench.

The numbers

Capacity with filter8.2 qt (7.8 L)
Capacity without filter7.8 qt (7.4 L)
Dry fill (2010 manual)9.9 qt (9.4 L), for an engine with no oil in it, not for a normal change
Oil typeILSAC multigrade engine oil
ViscositySAE 0W-20 (preferred). SAE 5W-20 is allowed if 0W-20 is not available, and must be replaced at the next oil change.
Drain plug torque40 N·m (30 ft-lb), with a new gasket
Oil filter cap torque25 N·m (18 ft-lb), using the special tool
Oil filter cap toolToyota SST 09228-06501
Engine under cover seal bolts (2)29 N·m (21 ft-lb)
Normal scheduleOil and oil filter: replace at the mileage interval or every 12 months, whichever comes first (10,000 mi).
Severe scheduleOil and oil filter: replace at the mileage interval or every 6 months, whichever occurs first.
Level checkWarm the engine, stop it, wait 5 minutes, read the dipstick between the low and full marks.

Parts and fluid

PositionProductNote
Engine oil · SAE 0W-20AMSOIL Signature Series 0W-20 100% Synthetic Motor OilToyota's capacity with a filter change is 8.2 US qt (7.8 L), so plan on nine quarts to have a spare.Buy on AMSOIL.com
Engine oil filterAMSOIL Ea Oil Filter EA15K49This is AMSOIL's published fitment for the GX 4.6L. The repair manual prints no filter part number, so confirm it against your engine before you buy.Buy on AMSOIL.com

Tools

Procedure

  1. Decide which schedule you are on. Toyota prints two schedules. On the normal schedule the engine oil and the engine oil filter are both under Replace at 10,000 miles, at the mileage interval or every 12 months, whichever comes first. On the severe schedule the same two items are replaced at the mileage interval or every 6 months, whichever occurs first. There is one condition on the normal schedule: the 15,000-mile page lists the oil and filter again only if 0W-20 was not used at the last oil change. If you ran 5W-20 as the manual's fallback, do not wait for the next interval; change it.
  2. Raise the vehicle and open the engine. Put the vehicle level on a lift or on jack stands with the wheels chocked. Remove the 2 bolts and the engine under cover seal, then remove the oil filler cap. Opening the filler cap first lets the oil drain freely.
  3. Drain the oil and refit the plug. Remove the oil pan drain plug and its gasket and drain the engine oil into a container. Install a new gasket and the drain plug and torque it to 40 N·m (30 ft-lb).
  4. Remove the covers that block the filter. The manual's next two operations are removing the lower front bumper cover and then the No. 1 engine under cover sub-assembly. Each is a separate removal procedure in the manual that this guide does not reproduce, so follow your own truck's layout: these are the covers the manual removes before it reaches the filter cap.
  5. Loosen the filter cap and let it drain. Using the special tool (SST 09228-06501), loosen the oil filter cap 4 revolutions, align the cap ribs vertically and let the remaining oil drain from the gap between the cap and the oil pan into a container. Do not remove the oil filter bracket clip when you take the cap off.
  6. Remove the cap, the element and the O-ring. Remove the oil filter cap, then remove the filter element and the O-ring from it. Remove the O-ring by hand, without any tool, because a tool can damage the groove for the O-ring on the cap.
  7. Prepare the new element and O-ring. Clean the inside of the cap, its threads and the O-ring groove. Apply a small amount of engine oil to a new O-ring and fit it to the cap. Set a new oil filter element in the cap. Remove any dirt or foreign matter from the installation surface and from inside the engine.
  8. Fit and torque the filter cap. Reapply a small amount of engine oil to the cap O-ring. Align the cap with the oil filter bracket so that the cutout in the cap threads sits 90 degrees from the groove in the bracket, then temporarily install it, making sure the O-ring does not get caught between the parts. Using the special tool, tighten the cap to 25 N·m (18 ft-lb). Afterwards check for gaps between the installation surfaces. Do not cross-thread the cap, and do not remove the bracket clip while installing it.
  9. Add oil and close up. Add fresh engine oil. Toyota's capacity with a filter change is 8.2 US qt (7.8 L). The manual's own oil grade and capacity lines on the replacement page are blank in the text we hold, so the figures here come from its specification pages. Install the oil filler cap, then refit the engine under cover seal with its 2 bolts at 29 N·m (21 ft-lb).
  10. Start it and look for leaks. Start the engine and make sure there are no oil leaks from the area you worked on: the drain plug and the filter cap. Then refit the No. 1 engine under cover sub-assembly and the lower front bumper cover.
  11. Check the level. Warm up the engine, then stop it and wait for 5 minutes. Check that the oil level is between the low and full marks on the dipstick. If it is low, check for leakage and add oil up to the full mark. Do not fill above the full mark. While you are looking, Toyota also asks you to check the oil for deterioration, water contamination, discoloration or thinning.
  12. Reset the oil maintenance data. On a vehicle without the navigation system, the manual's reset runs like this. Press the menu switch to change the multi-information display to blank. Turn the ENGINE START STOP switch off. While pressing the ODO/TRIP button, turn the switch to IGNITION ON mode, and keep holding the button for more than 7 seconds. The display shows RESETTING OIL MAINTENANCE DATA and after 5 seconds the reset is complete. We hold only the without-navigation procedure; if your truck has navigation, use the owner's manual.

Oil type, viscosity, capacity and both maintenance schedules are quoted from the Lexus GX 460 (4.6L 1UR-FE) repair manual for the 2010 model year and verified identical in the 2013 manual. The replacement procedure, torque figures, special tool number, level check and the oil reminder reset are from the 2010 manual only; the 2013 text we hold does not contain them. The archive has no GX 460 manual after 2013, so 2014 to 2023 is not separately verified; confirm the specification for your exact year and torque to spec. The manual prints no filter part number, and AMSOIL's coverage of the oil and filter is AMSOIL's published claim. Tuned Yota is an Independent Authorized AMSOIL Dealer; every Buy link opens the product on amsoil.com.

Frequently asked questions

How much oil does a Lexus GX 460 take?
8.2 US quarts (7.8 L) with a filter change, and 7.8 US quarts (7.4 L) without one. Both the 2010 and the 2013 repair manuals print the same two figures. The 2010 manual also lists a dry fill of 9.9 qt (9.4 L), which applies to an engine with no oil in it, not to a normal change.
What oil does a GX 460 take?
An ILSAC multigrade engine oil, viscosity SAE 0W-20, which Toyota marks as preferred. If SAE 0W-20 is not available, SAE 5W-20 may be used, but the manual says it must be replaced at the next oil change.
What is the drain plug torque on a GX 460?
40 N·m (30 ft-lb), and the manual calls for a new gasket under the plug. The oil filter cap is a separate figure, 25 N·m (18 ft-lb), and the two bolts of the engine under cover seal are 29 N·m (21 ft-lb).
How often should a GX 460 oil change be done?
On Toyota's normal schedule, the engine oil and oil filter are replaced at the mileage interval or every 12 months, whichever comes first, starting at 10,000 miles. On the severe schedule, it is the mileage interval or every 6 months, whichever occurs first. If 5W-20 was used at the last change, the 15,000-mile entry means the oil and filter come due then too.
Does the GX 460 oil filter need a special tool?
The manual uses a special tool, SST 09228-06501, to loosen and tighten the oil filter cap. The filter is a cartridge element inside a cap, so there is a new element and a new O-ring on every change, and the cap is torqued to 25 N·m.
Does this apply to a 2014 to 2023 GX 460?
We have verified the capacity, the oil grade and both schedules in the 2010 and 2013 manuals, and they match. The procedure and torque figures come from the 2010 manual only. The archive we work from has no GX 460 manual after 2013, so 2014 to 2023 is not separately verified. Check your own year before you rely on any figure.