Tuned Yota · Independent Authorized AMSOIL Dealer · Lakeville, Minnesota, USA · This website is owned and operated by an independent AMSOIL Dealer and is not AMSOIL INC.

Tuned Yota FluidsIndependent Authorized AMSOIL Dealer

Service Guide · Toyota Sequoia · 4.7L V8 (2UZ-FE)

Sequoia 4.7L (2UZ-FE) Oil Capacity (6.6 qt), Grade (5W-30) and Oil and Filter Change

The 4.7L Sequoia takes SAE 5W-30 and 6.6 US quarts with the filter (6.0 without). Both Toyota manuals we have, the 2001 and the 2008, print the same two numbers. They differ on the drain plug torque: the 2001 manual says 39 N·m (29 ft-lb), the 2008 manual says 40 N·m (30 ft-lb) in one step and 39 N·m (29 ft-lb) in another. Every number below is quoted from a Toyota repair manual, and anything the manuals leave blank is marked as blank.

Safety. Required: safety glasses, gloves, and the truck level on a lift or on jack stands with the wheels chocked. Recommended: a drain pan, a torque wrench, and the filter wrench. Toyota's own caution on this job: used engine oil removes the natural oils from skin and contains contaminants, so wear gloves that oil cannot penetrate, wash with soap and water, and take used oil and filters to a designated disposal site.

The numbers

Oil grade, 2008 manualILSAC multigrade oil, SAE 5W-30 for the 4.7L
Oil grade, 2001 manualAPI SJ Energy-Conserving or ILSAC multigrade engine oil, SAE 5W-30. The owner's section adds: SAE 5W-30 is the best choice for good fuel economy and good starting in cold weather.
Capacity, both manuals6.6 US qt (6.2 L) with the filter; 6.0 US qt (5.7 L) without
Dry fill, 2001 manual7.5 US qt (7.1 L). The 2008 manual prints no dry-fill figure for the 4.7L.
Oil pan drain plug, 2001 manual39 N·m (29 ft-lb), new gasket
Oil pan drain plug, 2008 manual40 N·m (30 ft-lb) at the drain step and 39 N·m (29 ft-lb) at the refill step, new gasket. The manual disagrees with itself by 1 N·m.
Oil filter, 2008 manualTighten with SST 09228-07501 to 17 N·m (13 ft-lb), or, if there is no room for a torque wrench, 3/4 turn after the gasket contacts the seat
Oil filter, 2001 manualHand-tighten until the gasket contacts the seat, then SST 09228-07501 for an additional 3/4 turn. No torque-wrench value is printed.
No. 1 engine under cover, 2008 manual3 screws and 5 bolts. Bolt 29 N·m (21 ft-lb), screw 3.0 N·m (27 in-lb). The 2001 manual prints no under cover torque.
Level checkWarm the engine, stop it, wait 5 minutes (2008 manual), then read the dipstick between the low and full marks
Interval, 2008 manualNormal service lists the oil and filter at 5,000 miles, or every 6 months, whichever comes first. Reset the MAINT REQD light afterward if the truck has one.

Parts and fluid

PositionProductNote
Engine oil · SAE 5W-30AMSOIL Signature Series 5W-30 100% Synthetic Motor OilTakes 6.6 qt with the filter, so order 7. AMSOIL's lookup lists this oil for the Sequoia 4.7L V8; confirm it for your year.Buy on AMSOIL.com
Oil filter · AMSOIL EaAMSOIL Ea Oil Filter EA15K51AMSOIL lists this filter for the Sequoia 4.7L V8. Neither manual prints a filter part number we can quote, so confirm fitment for your year.Buy on AMSOIL.com
Gasket · Toyota dealerOil pan drain plug gasketBoth Toyota procedures install the drain plug with a new gasket every time

Tools

Procedure

  1. Remove the No. 1 engine under cover. Park level, on a lift or on jack stands with the wheels chocked. In the 2008 manual the under cover comes off first: remove the 3 screws and 5 bolts, then unhook the cover from the vehicle body.
  2. Drain the pan. Remove the oil filler cap so the pan drains freely. Remove the oil drain plug and gasket and drain the engine oil into a container.
  3. Change the filter. Use SST 09228-07501 to remove the oil filter. Clean the oil filter contact surface on the mounting and lubricate the new filter's rubber gasket with clean engine oil. Screw the filter on by hand until the gasket contacts the seat. Then finish it Toyota's way: the 2008 manual tightens it with the SST to 17 N·m (13 ft-lb), or 3/4 turn if there is no room for a torque wrench; the 2001 manual gives an additional 3/4 turn with the SST.
  4. Refit the drain plug with a new gasket. Clean the plug and install it with a NEW gasket. The 2001 manual says 39 N·m (29 ft-lb). The 2008 manual says 40 N·m (30 ft-lb) at the drain step and 39 N·m (29 ft-lb) at the refill step. The two figures are one newton-metre apart; pick one and be consistent.
  5. Fill the oil, then set the level. Fresh oil is 6.6 US qt (6.2 L) with the filter. The replacement pages in both manuals print the capacity line blank in the text we have, so the figure comes from the specification pages. Pour a little short of it, reinstall the filler cap, then check. Toyota's method: warm the engine, stop it, wait 5 minutes, and read the dipstick. The level belongs between the low and full marks, and if it is low, check for leakage and add oil up to the full mark. Toyota is explicit: do not fill engine oil above the full mark.
  6. Check for leaks and close up. Start the engine and make sure there are no oil leaks from the area that was worked on. Hook the under cover back onto the body and install the 3 screws and 5 bolts (2008 manual: bolts 29 N·m / 21 ft-lb, screws 3.0 N·m / 27 in-lb). Reset the oil replacement reminder (MAINT REQD) light if the truck has one.

Grade, capacity, torques and procedure are quoted from the Toyota repair manuals for the 4.7L V8 (2UZ-FE) Sequoia: the 2001 manual and the 2008 manual. Years other than 2001 and 2008 are not separately verified here, and the 5.7L is not covered. Where the manuals differ, both figures are shown. Torque to spec. AMSOIL's coverage of this application is AMSOIL's published claim. Tuned Yota is an Independent Authorized AMSOIL Dealer; every Buy link opens the product on amsoil.com.

Frequently asked questions

What oil does a 4.7L Sequoia take?
SAE 5W-30. The 2008 manual specifies ILSAC multigrade oil in 5W-30 for the 4.7L. The 2001 manual specifies API SJ Energy-Conserving or ILSAC multigrade engine oil in SAE 5W-30, and its owner's section calls 5W-30 the best choice for fuel economy and cold-weather starting.
How many quarts does a 4.7L Sequoia take?
6.6 US quarts (6.2 L) with the filter and 6.0 US quarts (5.7 L) without, in both the 2001 and the 2008 manual. The 2001 manual also prints a dry-fill figure of 7.5 US quarts (7.1 L). The 2008 manual lists a 5.7L engine on the same page; that engine has different numbers and this guide does not cover it.
What torque does the drain plug take?
The manuals do not agree. The 2001 manual says 39 N·m (29 ft-lb). The 2008 manual says 40 N·m (30 ft-lb) at the drain step and 39 N·m (29 ft-lb) at the refill step. Always with a new gasket. The difference is one newton-metre, which is rounding, but we are not going to tell you one number is the only one.
How tight does the oil filter go?
It depends on the manual. The 2008 manual gives 17 N·m (13 ft-lb) with the SST if a torque wrench fits, or 3/4 turn by hand or with a common wrench if it does not. The 2001 manual prints no torque value: hand-tighten until the gasket contacts the seat, then an additional 3/4 turn with the SST.
How often should a 4.7L Sequoia get an oil change?
The 2008 manual's normal-service schedule lists the engine oil and oil filter at 5,000 miles, or every 6 months, whichever comes first. The 2001 manual carries a 7,500-mile normal schedule and a 5,000-mile severe schedule as page headings, but the text we have does not print the oil-specific wording, so we do not quote an interval for it. Use the book for your own truck.
Does this cover the 5.7L Sequoia?
No. This guide is written only from the 4.7L (2UZ-FE) pages of the 2001 and 2008 manuals. The 5.7L Sequoia is a different engine with a different grade and capacity, and we have not sourced it here.