Service Guide · Toyota Tundra 2007–2021 · 5.7L V8 (3UR-FE)
Tundra 5.7L Differential and Transfer Case Fluid: 2007 and 2016-2021 Manuals
The differentials are the same in both manuals. The transfer case is not. Front and rear differentials take Toyota Genuine Differential Gear Oil LT, 75W-85, API GL-5 (or equivalent), and the drain and filler plug torques match in the 2007 and the 2016-era repair manuals: 39 N·m (29 ft-lb) front, 49 N·m (36 ft-lb) rear. The transfer case changed. The 2007 manual says SAE 75W-90, about 1.1 liters, plugs at 37 N·m (27 ft-lb). The 2016-era manual says Toyota Genuine Transfer Gear Oil LF, SAE 75W, 1.4 to 1.5 liters, plugs at 25 N·m (18 ft-lb). We verified those two books only. If your truck is a 2008 to mid-2015 build, confirm the transfer case spec before you fill.
Safety. Required: safety glasses, gloves, and the truck level on a lift or on jack stands with the wheels chocked. Recommended: a drain pan, a torque wrench and a fluid pump, because these fills go in from underneath through the filler hole. Toyota's notice on both units: too much or too little oil will lead to problems, so set the level exactly, then drive the truck and check it again.
The numbers
| Differential fluid, front and rear (both manuals) | Toyota Genuine Differential Gear Oil LT, 75W-85, API GL-5 or equivalent |
|---|---|
| Front differential capacity, 2007 manual | 2.10 liters (2.2 US qt) |
| Front differential capacity, 2016-era manual | 2.00 to 2.10 liters (2.12 to 2.21 US qt) |
| Rear differential capacity, 2007 manual | 3.45 to 3.75 liters (3.6 to 4.0 US qt) by cab and bed |
| Rear differential capacity, 2016-era manual | 3.45 to 3.85 liters, up to 4.01 US qt (3UR engines; varies by cab and bed) |
| Front differential drain and filler plug (both manuals) | 39 N·m (29 ft-lb), new gasket |
| Rear differential drain and filler plug (both manuals) | 49 N·m (36 ft-lb), new gasket |
| Differential level (both manuals) | Oil between 0 and 5 mm from the bottom lip of the filler plug hole |
| Transfer case oil, 2007 manual | SAE 75W-90. The same manual labels the grade GL-3 on one page and GL-4 or GL-5 on another. |
| Transfer case capacity, 2007 manual | 1.1 ± 0.06 liters (1.2 US qt) on the inspection page; 1.03 liters (1.1 US qt) on the specifications page |
| Transfer case plugs, 2007 manual | 37 N·m (27 ft-lb) drain and filler; lower protector bolts 18 N·m (13 ft-lb) |
| Transfer case oil, 2016-era manual | Toyota Genuine Transfer Gear Oil LF or equivalent, SAE 75W |
| Transfer case capacity, 2016-era manual | 1.4 to 1.5 liters (1.48 to 1.58 US qt) |
| Transfer case plugs, 2016-era manual | 25 N·m (18 ft-lb) drain and filler, new plugs; lower protector 22 N·m (16 ft-lb) |
| Transfer case level (both manuals) | Oil between 0 and 5.0 mm from the bottom lip of the filler plug hole |
Parts and fluid
| Position | Product | Note | |
|---|---|---|---|
| Front differential (4WD) · 75W-85 GL-5 | AMSOIL Severe Gear 75W-85 100% Synthetic Gear Lube | The 2007 manual gives 2.10 liters (2.2 US qt). The 2016-era manual gives 2.00 to 2.10 liters (2.12 to 2.21 US qt). | Buy on AMSOIL.com |
| Rear differential · 75W-85 GL-5 | AMSOIL Severe Gear 75W-85 100% Synthetic Gear Lube | Same fluid as the front. Capacity depends on cab and bed: 3.45 to 3.75 liters in the 2007 manual, 3.45 to 3.85 liters in the 2016-era manual. Seven quarts covers a front and a rear on any truck in either book. | Buy on AMSOIL.com |
| Transfer case (4WD) | Look up your truck in the fluid lookup | The two manuals print different transfer case oils, so we do not name one product for every year. Use the lookup for your exact year, and check it against your own manual. |
Tools
- Torque wrench: 39, 49, 37 and 25 N·m, depending on the plug and the year
- 10 mm hex wrench for the differential plugs (2007 manual)
- Fluid pump for filling through the filler hole, and a drain pan
- Lift, or jack stands and wheel chocks; the truck must be level
- New gaskets for every plug you remove
- Safety glasses and gloves
Procedure
- Get the truck level and find the plugs. Toyota's first instruction for the differential is to stop the vehicle on a level place. Put the truck on a lift, or on jack stands with the wheels chocked, level side to side and front to back. You are working three separate units: the front differential (4WD), the rear differential and the transfer case (4WD). Each has a filler plug and a drain plug. Loosen every filler plug before you drain anything.
- Front differential: 75W-85 GL-5. The 2007 manual has you remove the filler plug and gasket, then the drain plug and gasket, with a 10 mm hex wrench. Let it drain. Install a new gasket and the drain plug at 39 N·m (29 ft-lb). The 2016-era manual gives the same 39 N·m (29 ft-lb) for the drain plug. Fill through the filler hole with Toyota Genuine Differential Gear Oil LT 75W-85 GL-5 or equivalent. The 2007 manual capacity is 2.10 liters (2.2 US qt); the 2016-era manual says 2.00 to 2.10 liters (2.12 to 2.21 US qt).
- Rear differential: same fluid, different amount. Same procedure and the same fluid. Drain plug and filler plug torque is 49 N·m (36 ft-lb) in both manuals, each with a new gasket. Capacity depends on your cab and bed. The 2007 manual lists 3.45 liters (3.6 US qt) for a Regular Cab standard bed up to 3.75 liters (4.0 US qt) for a Double Cab long bed or a two-wheel-drive CrewMax. The 2016-era manual lists 3.45 to 3.85 liters for the 3UR engines, in a table that varies by cab, bed length and build date. We read that table's merged cells as a range, not as a per-cab answer, so use the range and set the final level at the filler hole.
- Set the differential level, then drive and recheck. Add oil until it sits between 0 and 5 mm below the bottom lip of the filler plug hole. Toyota's notice: too much or too little oil will lead to differential problems. After changing the oil, drive the vehicle and then check the oil level again. Torque the filler plug with a new gasket: 39 N·m front, 49 N·m rear.
- Transfer case: remove the protector, filler plug first. The 2007 manual has you remove the 4 bolts and lower the transfer case protector, then remove the filler plug and gasket first, then the drain plug and gasket, and drain. Pulling the filler first matters: if the filler will not break loose after you have drained the case, you have an empty case and no way to refill it. The 2016-era manual calls for removing the filler and drain plugs and draining the transfer oil.
- Refill the transfer case to YOUR manual's spec. 2007 manual: install a new gasket and the drain plug at 37 N·m (27 ft-lb); pour slowly, a little at a time; wait about 5 minutes and recheck; install a new gasket and filler plug at 37 N·m (27 ft-lb). Refit the protector with its 4 bolts at 18 N·m (13 ft-lb). 2016-era manual: install a new drain plug at 25 N·m (18 ft-lb), add slowly, wait approximately 5 minutes and check the level has not changed, then install a new filler plug at 25 N·m (18 ft-lb). In both, the level is between 0 and 5.0 mm below the bottom lip of the filler hole. The fluid is different between the books, so fill the one that matches your truck.
Fluid grades, capacities, torques and level checks are quoted from two Toyota repair manuals for the 5.7L V8 (3UR-FE) Tundra: the 2007 manual, and the later manual whose replacement pages carry Toyota's own build-date bands (08/2015 onward). Model years 2008 through mid-2015 are not separately verified here, and neither are builds after 08/2019 for the transfer case. Where the two manuals disagree, each figure is labelled with its manual. Confirm the specification for your exact year and build date, and torque to spec. AMSOIL's coverage of this application is AMSOIL's published claim. Tuned Yota is an Independent Authorized AMSOIL Dealer; every Buy link opens the product on amsoil.com.